zlib.h

Go to the documentation of this file.

#ifndef _COMPAT_ZLIB_H
#define _COMPAT_ZLIB_H

#ifdef WANT_ZLIB

#ifdef RARCH_INTERNAL
#include "zconf.h.in"
#endif

/* zlib.h -- interface of the 'zlib' general purpose compression library
  version 1.2.8, April 28th, 2013

  Copyright (C) 1995-2013 Jean-loup Gailly and Mark Adler

  This software is provided 'as-is', without any express or implied
  warranty.  In no event will the authors be held liable for any damages
  arising from the use of this software.

  Permission is granted to anyone to use this software for any purpose,
  including commercial applications, and to alter it and redistribute it
  freely, subject to the following restrictions:

  1. The origin of this software must not be misrepresented; you must not
     claim that you wrote the original software. If you use this software
     in a product, an acknowledgment in the product documentation would be
     appreciated but is not required.
  2. Altered source versions must be plainly marked as such, and must not be
     misrepresented as being the original software.
  3. This notice may not be removed or altered from any source distribution.

  Jean-loup Gailly        Mark Adler
  [email protected]          [email protected]


  The data format used by the zlib library is described by RFCs (Request for
  Comments) 1950 to 1952 in the files http://tools.ietf.org/html/rfc1950
  (zlib format), rfc1951 (deflate format) and rfc1952 (gzip format).
*/

#ifndef ZLIB_H
#define ZLIB_H

#include <stdint.h>
#include "zconf.h"

#ifdef __cplusplus
extern "C" {
#endif

#define ZLIB_VERSION "1.2.8"
#define ZLIB_VERNUM 0x1280
#define ZLIB_VER_MAJOR 1
#define ZLIB_VER_MINOR 2
#define ZLIB_VER_REVISION 8
#define ZLIB_VER_SUBREVISION 0

/*
    The 'zlib' compression library provides in-memory compression and
  decompression functions, including integrity checks of the uncompressed data.
  This version of the library supports only one compression method (deflation)
  but other algorithms will be added later and will have the same stream
  interface.

    Compression can be done in a single step if the buffers are large enough,
  or can be done by repeated calls of the compression function.  In the latter
  case, the application must provide more input and/or consume the output
  (providing more output space) before each call.

    The compressed data format used by default by the in-memory functions is
  the zlib format, which is a zlib wrapper documented in RFC 1950, wrapped
  around a deflate stream, which is itself documented in RFC 1951.

    The library also supports reading and writing files in gzip (.gz) format
  with an interface similar to that of stdio using the functions that start
  with "gz".  The gzip format is different from the zlib format.  gzip is a
  gzip wrapper, documented in RFC 1952, wrapped around a deflate stream.

    This library can optionally read and write gzip streams in memory as well.

    The zlib format was designed to be compact and fast for use in memory
  and on communications channels.  The gzip format was designed for single-
  file compression on file systems, has a larger header than zlib to maintain
  directory information, and uses a different, slower check method than zlib.

    The library does not install any signal handler.  The decoder checks
  the consistency of the compressed data, so the library should never crash
  even in case of corrupted input.
*/

typedef voidpf (*alloc_func) (voidpf opaque, uInt items, uInt size);
typedef void   (*free_func)  (voidpf opaque, voidpf address);

struct internal_state;

typedef struct z_stream_s {
    z_const Bytef *next_in;     /* next input byte */
    uInt     avail_in;  /* number of bytes available at next_in */
    uLong    total_in;  /* total number of input bytes read so far */

    Bytef    *next_out; /* next output byte should be put there */
    uInt     avail_out; /* remaining free space at next_out */
    uLong    total_out; /* total number of bytes output so far */

    z_const char *msg;  /* last error message, NULL if no error */
    void *state; /* not visible by applications */

    alloc_func zalloc;  /* used to allocate the internal state */
    free_func  zfree;   /* used to free the internal state */
    voidpf     opaque;  /* private data object passed to zalloc and zfree */

    int     data_type;  /* best guess about the data type: binary or text */
    uLong   adler;      /* adler32 value of the uncompressed data */
    uLong   reserved;   /* reserved for future use */
} z_stream;

typedef z_stream FAR *z_streamp;

/*
     gzip header information passed to and from zlib routines.  See RFC 1952
  for more details on the meanings of these fields.
*/
typedef struct gz_header_s {
    int     text;       /* true if compressed data believed to be text */
    uLong   time;       /* modification time */
    int     xflags;     /* extra flags (not used when writing a gzip file) */
    int     os;         /* operating system */
    Bytef   *extra;     /* pointer to extra field or Z_NULL if none */
    uInt    extra_len;  /* extra field length (valid if extra != Z_NULL) */
    uInt    extra_max;  /* space at extra (only when reading header) */
    Bytef   *name;      /* pointer to zero-terminated file name or Z_NULL */
    uInt    name_max;   /* space at name (only when reading header) */
    Bytef   *comment;   /* pointer to zero-terminated comment or Z_NULL */
    uInt    comm_max;   /* space at comment (only when reading header) */
    int     hcrc;       /* true if there was or will be a header crc */
    int     done;       /* true when done reading gzip header (not used
                           when writing a gzip file) */
} gz_header;

typedef gz_header FAR *gz_headerp;

/*
     The application must update next_in and avail_in when avail_in has dropped
   to zero.  It must update next_out and avail_out when avail_out has dropped
   to zero.  The application must initialize zalloc, zfree and opaque before
   calling the init function.  All other fields are set by the compression
   library and must not be updated by the application.

     The opaque value provided by the application will be passed as the first
   parameter for calls of zalloc and zfree.  This can be useful for custom
   memory management.  The compression library attaches no meaning to the
   opaque value.

     zalloc must return Z_NULL if there is not enough memory for the object.
   If zlib is used in a multi-threaded application, zalloc and zfree must be
   thread safe.

     On 16-bit systems, the functions zalloc and zfree must be able to allocate
   exactly 65536 bytes, but will not be required to allocate more than this if
   the symbol MAXSEG_64K is defined (see zconf.h).  WARNING: On MSDOS, pointers
   returned by zalloc for objects of exactly 65536 bytes *must* have their
   offset normalized to zero.  The default allocation function provided by this
   library ensures this (see zutil.c).  To reduce memory requirements and avoid
   any allocation of 64K objects, at the expense of compression ratio, compile
   the library with -DMAX_WBITS=14 (see zconf.h).

     The fields total_in and total_out can be used for statistics or progress
   reports.  After compression, total_in holds the total size of the
   uncompressed data and may be saved for use in the decompressor (particularly
   if the decompressor wants to decompress everything in a single step).
*/

                        /* constants */

#define Z_NO_FLUSH      0
#define Z_PARTIAL_FLUSH 1
#define Z_SYNC_FLUSH    2
#define Z_FULL_FLUSH    3
#define Z_FINISH        4
#define Z_BLOCK         5
#define Z_TREES         6
/* Allowed flush values; see deflate() and inflate() below for details */

#define Z_OK            0
#define Z_STREAM_END    1
#define Z_NEED_DICT     2
#define Z_ERRNO        (-1)
#define Z_STREAM_ERROR (-2)
#define Z_DATA_ERROR   (-3)
#define Z_MEM_ERROR    (-4)
#define Z_BUF_ERROR    (-5)
#define Z_VERSION_ERROR (-6)
/* Return codes for the compression/decompression functions. Negative values
 * are errors, positive values are used for special but normal events.
 */

#define Z_NO_COMPRESSION         0
#define Z_BEST_SPEED             1
#define Z_BEST_COMPRESSION       9
#define Z_DEFAULT_COMPRESSION  (-1)
/* compression levels */

#define Z_FILTERED            1
#define Z_HUFFMAN_ONLY        2
#define Z_RLE                 3
#define Z_FIXED               4
#define Z_DEFAULT_STRATEGY    0
/* compression strategy; see deflateInit2() below for details */

#define Z_BINARY   0
#define Z_TEXT     1
#define Z_ASCII    Z_TEXT   /* for compatibility with 1.2.2 and earlier */
#define Z_UNKNOWN  2
/* Possible values of the data_type field (though see inflate()) */

#define Z_DEFLATED   8
/* The deflate compression method (the only one supported in this version) */

#define Z_NULL  0  /* for initializing zalloc, zfree, opaque */

#define zlib_version zlibVersion()
/* for compatibility with versions < 1.0.2 */


                        /* basic functions */

 const char * zlibVersion (void);
/* The application can compare zlibVersion and ZLIB_VERSION for consistency.
   If the first character differs, the library code actually used is not
   compatible with the zlib.h header file used by the application.  This check
   is automatically made by deflateInit and inflateInit.
 */

/*
 int deflateInit (z_streamp strm, int level);

     Initializes the internal stream state for compression.  The fields
   zalloc, zfree and opaque must be initialized before by the caller.  If
   zalloc and zfree are set to Z_NULL, deflateInit updates them to use default
   allocation functions.

     The compression level must be Z_DEFAULT_COMPRESSION, or between 0 and 9:
   1 gives best speed, 9 gives best compression, 0 gives no compression at all
   (the input data is simply copied a block at a time).  Z_DEFAULT_COMPRESSION
   requests a default compromise between speed and compression (currently
   equivalent to level 6).

     deflateInit returns Z_OK if success, Z_MEM_ERROR if there was not enough
   memory, Z_STREAM_ERROR if level is not a valid compression level, or
   Z_VERSION_ERROR if the zlib library version (zlib_version) is incompatible
   with the version assumed by the caller (ZLIB_VERSION).  msg is set to null
   if there is no error message.  deflateInit does not perform any compression:
   this will be done by deflate().
*/


 int deflate (z_streamp strm, int flush);
/*
    deflate compresses as much data as possible, and stops when the input
  buffer becomes empty or the output buffer becomes full.  It may introduce
  some output latency (reading input without producing any output) except when
  forced to flush.

    The detailed semantics are as follows.  deflate performs one or both of the
  following actions:

  - Compress more input starting at next_in and update next_in and avail_in
    accordingly.  If not all input can be processed (because there is not
    enough room in the output buffer), next_in and avail_in are updated and
    processing will resume at this point for the next call of deflate().

  - Provide more output starting at next_out and update next_out and avail_out
    accordingly.  This action is forced if the parameter flush is non zero.
    Forcing flush frequently degrades the compression ratio, so this parameter
    should be set only when necessary (in interactive applications).  Some
    output may be provided even if flush is not set.

    Before the call of deflate(), the application should ensure that at least
  one of the actions is possible, by providing more input and/or consuming more
  output, and updating avail_in or avail_out accordingly; avail_out should
  never be zero before the call.  The application can consume the compressed
  output when it wants, for example when the output buffer is full (avail_out
  == 0), or after each call of deflate().  If deflate returns Z_OK and with
  zero avail_out, it must be called again after making room in the output
  buffer because there might be more output pending.

    Normally the parameter flush is set to Z_NO_FLUSH, which allows deflate to
  decide how much data to accumulate before producing output, in order to
  maximize compression.

    If the parameter flush is set to Z_SYNC_FLUSH, all pending output is
  flushed to the output buffer and the output is aligned on a byte boundary, so
  that the decompressor can get all input data available so far.  (In
  particular avail_in is zero after the call if enough output space has been
  provided before the call.) Flushing may degrade compression for some
  compression algorithms and so it should be used only when necessary.  This
  completes the current deflate block and follows it with an empty stored block
  that is three bits plus filler bits to the next byte, followed by four bytes
  (00 00 ff ff).

    If flush is set to Z_PARTIAL_FLUSH, all pending output is flushed to the
  output buffer, but the output is not aligned to a byte boundary.  All of the
  input data so far will be available to the decompressor, as for Z_SYNC_FLUSH.
  This completes the current deflate block and follows it with an empty fixed
  codes block that is 10 bits long.  This assures that enough bytes are output
  in order for the decompressor to finish the block before the empty fixed code
  block.

    If flush is set to Z_BLOCK, a deflate block is completed and emitted, as
  for Z_SYNC_FLUSH, but the output is not aligned on a byte boundary, and up to
  seven bits of the current block are held to be written as the next byte after
  the next deflate block is completed.  In this case, the decompressor may not
  be provided enough bits at this point in order to complete decompression of
  the data provided so far to the compressor.  It may need to wait for the next
  block to be emitted.  This is for advanced applications that need to control
  the emission of deflate blocks.

    If flush is set to Z_FULL_FLUSH, all output is flushed as with
  Z_SYNC_FLUSH, and the compression state is reset so that decompression can
  restart from this point if previous compressed data has been damaged or if
  random access is desired.  Using Z_FULL_FLUSH too often can seriously degrade
  compression.

    If deflate returns with avail_out == 0, this function must be called again
  with the same value of the flush parameter and more output space (updated
  avail_out), until the flush is complete (deflate returns with non-zero
  avail_out).  In the case of a Z_FULL_FLUSH or Z_SYNC_FLUSH, make sure that
  avail_out is greater than six to avoid repeated flush markers due to
  avail_out == 0 on return.

    If the parameter flush is set to Z_FINISH, pending input is processed,
  pending output is flushed and deflate returns with Z_STREAM_END if there was
  enough output space; if deflate returns with Z_OK, this function must be
  called again with Z_FINISH and more output space (updated avail_out) but no
  more input data, until it returns with Z_STREAM_END or an error.  After
  deflate has returned Z_STREAM_END, the only possible operations on the stream
  are deflateReset or deflateEnd.

    Z_FINISH can be used immediately after deflateInit if all the compression
  is to be done in a single step.  In this case, avail_out must be at least the
  value returned by deflateBound (see below).  Then deflate is guaranteed to
  return Z_STREAM_END.  If not enough output space is provided, deflate will
  not return Z_STREAM_END, and it must be called again as described above.

    deflate() sets strm->adler to the adler32 checksum of all input read
  so far (that is, total_in bytes).

    deflate() may update strm->data_type if it can make a good guess about
  the input data type (Z_BINARY or Z_TEXT).  In doubt, the data is considered
  binary.  This field is only for information purposes and does not affect the
  compression algorithm in any manner.

    deflate() returns Z_OK if some progress has been made (more input
  processed or more output produced), Z_STREAM_END if all input has been
  consumed and all output has been produced (only when flush is set to
  Z_FINISH), Z_STREAM_ERROR if the stream state was inconsistent (for example
  if next_in or next_out was Z_NULL), Z_BUF_ERROR if no progress is possible
  (for example avail_in or avail_out was zero).  Note that Z_BUF_ERROR is not
  fatal, and deflate() can be called again with more input and more output
  space to continue compressing.
*/


 int deflateEnd (z_streamp strm);
/*
     All dynamically allocated data structures for this stream are freed.
   This function discards any unprocessed input and does not flush any pending
   output.

     deflateEnd returns Z_OK if success, Z_STREAM_ERROR if the
   stream state was inconsistent, Z_DATA_ERROR if the stream was freed
   prematurely (some input or output was discarded).  In the error case, msg
   may be set but then points to a static string (which must not be
   deallocated).
*/


/*
 int inflateInit (z_streamp strm);

     Initializes the internal stream state for decompression.  The fields
   next_in, avail_in, zalloc, zfree and opaque must be initialized before by
   the caller.  If next_in is not Z_NULL and avail_in is large enough (the
   exact value depends on the compression method), inflateInit determines the
   compression method from the zlib header and allocates all data structures
   accordingly; otherwise the allocation will be deferred to the first call of
   inflate.  If zalloc and zfree are set to Z_NULL, inflateInit updates them to
   use default allocation functions.

     inflateInit returns Z_OK if success, Z_MEM_ERROR if there was not enough
   memory, Z_VERSION_ERROR if the zlib library version is incompatible with the
   version assumed by the caller, or Z_STREAM_ERROR if the parameters are
   invalid, such as a null pointer to the structure.  msg is set to null if
   there is no error message.  inflateInit does not perform any decompression
   apart from possibly reading the zlib header if present: actual decompression
   will be done by inflate().  (So next_in and avail_in may be modified, but
   next_out and avail_out are unused and unchanged.) The current implementation
   of inflateInit() does not process any header information -- that is deferred
   until inflate() is called.
*/


 int inflate (z_streamp strm, int flush);
/*
    inflate decompresses as much data as possible, and stops when the input
  buffer becomes empty or the output buffer becomes full.  It may introduce
  some output latency (reading input without producing any output) except when
  forced to flush.

  The detailed semantics are as follows.  inflate performs one or both of the
  following actions:

  - Decompress more input starting at next_in and update next_in and avail_in
    accordingly.  If not all input can be processed (because there is not
    enough room in the output buffer), next_in is updated and processing will
    resume at this point for the next call of inflate().

  - Provide more output starting at next_out and update next_out and avail_out
    accordingly.  inflate() provides as much output as possible, until there is
    no more input data or no more space in the output buffer (see below about
    the flush parameter).

    Before the call of inflate(), the application should ensure that at least
  one of the actions is possible, by providing more input and/or consuming more
  output, and updating the next_* and avail_* values accordingly.  The
  application can consume the uncompressed output when it wants, for example
  when the output buffer is full (avail_out == 0), or after each call of
  inflate().  If inflate returns Z_OK and with zero avail_out, it must be
  called again after making room in the output buffer because there might be
  more output pending.

    The flush parameter of inflate() can be Z_NO_FLUSH, Z_SYNC_FLUSH, Z_FINISH,
  Z_BLOCK, or Z_TREES.  Z_SYNC_FLUSH requests that inflate() flush as much
  output as possible to the output buffer.  Z_BLOCK requests that inflate()
  stop if and when it gets to the next deflate block boundary.  When decoding
  the zlib or gzip format, this will cause inflate() to return immediately
  after the header and before the first block.  When doing a raw inflate,
  inflate() will go ahead and process the first block, and will return when it
  gets to the end of that block, or when it runs out of data.

    The Z_BLOCK option assists in appending to or combining deflate streams.
  Also to assist in this, on return inflate() will set strm->data_type to the
  number of unused bits in the last byte taken from strm->next_in, plus 64 if
  inflate() is currently decoding the last block in the deflate stream, plus
  128 if inflate() returned immediately after decoding an end-of-block code or
  decoding the complete header up to just before the first byte of the deflate
  stream.  The end-of-block will not be indicated until all of the uncompressed
  data from that block has been written to strm->next_out.  The number of
  unused bits may in general be greater than seven, except when bit 7 of
  data_type is set, in which case the number of unused bits will be less than
  eight.  data_type is set as noted here every time inflate() returns for all
  flush options, and so can be used to determine the amount of currently
  consumed input in bits.

    The Z_TREES option behaves as Z_BLOCK does, but it also returns when the
  end of each deflate block header is reached, before any actual data in that
  block is decoded.  This allows the caller to determine the length of the
  deflate block header for later use in random access within a deflate block.
  256 is added to the value of strm->data_type when inflate() returns
  immediately after reaching the end of the deflate block header.

    inflate() should normally be called until it returns Z_STREAM_END or an
  error.  However if all decompression is to be performed in a single step (a
  single call of inflate), the parameter flush should be set to Z_FINISH.  In
  this case all pending input is processed and all pending output is flushed;
  avail_out must be large enough to hold all of the uncompressed data for the
  operation to complete.  (The size of the uncompressed data may have been
  saved by the compressor for this purpose.) The use of Z_FINISH is not
  required to perform an inflation in one step.  However it may be used to
  inform inflate that a faster approach can be used for the single inflate()
  call.  Z_FINISH also informs inflate to not maintain a sliding window if the
  stream completes, which reduces inflate's memory footprint.  If the stream
  does not complete, either because not all of the stream is provided or not
  enough output space is provided, then a sliding window will be allocated and
  inflate() can be called again to continue the operation as if Z_NO_FLUSH had
  been used.

     In this implementation, inflate() always flushes as much output as
  possible to the output buffer, and always uses the faster approach on the
  first call.  So the effects of the flush parameter in this implementation are
  on the return value of inflate() as noted below, when inflate() returns early
  when Z_BLOCK or Z_TREES is used, and when inflate() avoids the allocation of
  memory for a sliding window when Z_FINISH is used.

     If a preset dictionary is needed after this call (see inflateSetDictionary
  below), inflate sets strm->adler to the Adler-32 checksum of the dictionary
  chosen by the compressor and returns Z_NEED_DICT; otherwise it sets
  strm->adler to the Adler-32 checksum of all output produced so far (that is,
  total_out bytes) and returns Z_OK, Z_STREAM_END or an error code as described
  below.  At the end of the stream, inflate() checks that its computed adler32
  checksum is equal to that saved by the compressor and returns Z_STREAM_END
  only if the checksum is correct.

    inflate() can decompress and check either zlib-wrapped or gzip-wrapped
  deflate data.  The header type is detected automatically, if requested when
  initializing with inflateInit2().  Any information contained in the gzip
  header is not retained, so applications that need that information should
  instead use raw inflate, see inflateInit2() below, or inflateBack() and
  perform their own processing of the gzip header and trailer.  When processing
  gzip-wrapped deflate data, strm->adler32 is set to the CRC-32 of the output
  producted so far.  The CRC-32 is checked against the gzip trailer.

    inflate() returns Z_OK if some progress has been made (more input processed
  or more output produced), Z_STREAM_END if the end of the compressed data has
  been reached and all uncompressed output has been produced, Z_NEED_DICT if a
  preset dictionary is needed at this point, Z_DATA_ERROR if the input data was
  corrupted (input stream not conforming to the zlib format or incorrect check
  value), Z_STREAM_ERROR if the stream structure was inconsistent (for example
  next_in or next_out was Z_NULL), Z_MEM_ERROR if there was not enough memory,
  Z_BUF_ERROR if no progress is possible or if there was not enough room in the
  output buffer when Z_FINISH is used.  Note that Z_BUF_ERROR is not fatal, and
  inflate() can be called again with more input and more output space to
  continue decompressing.  If Z_DATA_ERROR is returned, the application may
  then call inflateSync() to look for a good compression block if a partial
  recovery of the data is desired.
*/


 int inflateEnd (z_streamp strm);
/*
     All dynamically allocated data structures for this stream are freed.
   This function discards any unprocessed input and does not flush any pending
   output.

     inflateEnd returns Z_OK if success, Z_STREAM_ERROR if the stream state
   was inconsistent.  In the error case, msg may be set but then points to a
   static string (which must not be deallocated).
*/


                        /* Advanced functions */

/*
    The following functions are needed only in some special applications.
*/

/*
 int deflateInit2 (z_streamp strm,
                                     int  level,
                                     int  method,
                                     int  windowBits,
                                     int  memLevel,
                                     int  strategy);

     This is another version of deflateInit with more compression options.  The
   fields next_in, zalloc, zfree and opaque must be initialized before by the
   caller.

     The method parameter is the compression method.  It must be Z_DEFLATED in
   this version of the library.

     The windowBits parameter is the base two logarithm of the window size
   (the size of the history buffer).  It should be in the range 8..15 for this
   version of the library.  Larger values of this parameter result in better
   compression at the expense of memory usage.  The default value is 15 if
   deflateInit is used instead.

     windowBits can also be -8..-15 for raw deflate.  In this case, -windowBits
   determines the window size.  deflate() will then generate raw deflate data
   with no zlib header or trailer, and will not compute an adler32 check value.

     windowBits can also be greater than 15 for optional gzip encoding.  Add
   16 to windowBits to write a simple gzip header and trailer around the
   compressed data instead of a zlib wrapper.  The gzip header will have no
   file name, no extra data, no comment, no modification time (set to zero), no
   header crc, and the operating system will be set to 255 (unknown).  If a
   gzip stream is being written, strm->adler is a crc32 instead of an adler32.

     The memLevel parameter specifies how much memory should be allocated
   for the internal compression state.  memLevel=1 uses minimum memory but is
   slow and reduces compression ratio; memLevel=9 uses maximum memory for
   optimal speed.  The default value is 8.  See zconf.h for total memory usage
   as a function of windowBits and memLevel.

     The strategy parameter is used to tune the compression algorithm.  Use the
   value Z_DEFAULT_STRATEGY for normal data, Z_FILTERED for data produced by a
   filter (or predictor), Z_HUFFMAN_ONLY to force Huffman encoding only (no
   string match), or Z_RLE to limit match distances to one (run-length
   encoding).  Filtered data consists mostly of small values with a somewhat
   random distribution.  In this case, the compression algorithm is tuned to
   compress them better.  The effect of Z_FILTERED is to force more Huffman
   coding and less string matching; it is somewhat intermediate between
   Z_DEFAULT_STRATEGY and Z_HUFFMAN_ONLY.  Z_RLE is designed to be almost as
   fast as Z_HUFFMAN_ONLY, but give better compression for PNG image data.  The
   strategy parameter only affects the compression ratio but not the
   correctness of the compressed output even if it is not set appropriately.
   Z_FIXED prevents the use of dynamic Huffman codes, allowing for a simpler
   decoder for special applications.

     deflateInit2 returns Z_OK if success, Z_MEM_ERROR if there was not enough
   memory, Z_STREAM_ERROR if any parameter is invalid (such as an invalid
   method), or Z_VERSION_ERROR if the zlib library version (zlib_version) is
   incompatible with the version assumed by the caller (ZLIB_VERSION).  msg is
   set to null if there is no error message.  deflateInit2 does not perform any
   compression: this will be done by deflate().
*/

 int deflateSetDictionary (z_streamp strm,
                                             const Bytef *dictionary,
                                             uInt  dictLength);
/*
     Initializes the compression dictionary from the given byte sequence
   without producing any compressed output.  When using the zlib format, this
   function must be called immediately after deflateInit, deflateInit2 or
   deflateReset, and before any call of deflate.  When doing raw deflate, this
   function must be called either before any call of deflate, or immediately
   after the completion of a deflate block, i.e. after all input has been
   consumed and all output has been delivered when using any of the flush
   options Z_BLOCK, Z_PARTIAL_FLUSH, Z_SYNC_FLUSH, or Z_FULL_FLUSH.  The
   compressor and decompressor must use exactly the same dictionary (see
   inflateSetDictionary).

     The dictionary should consist of strings (byte sequences) that are likely
   to be encountered later in the data to be compressed, with the most commonly
   used strings preferably put towards the end of the dictionary.  Using a
   dictionary is most useful when the data to be compressed is short and can be
   predicted with good accuracy; the data can then be compressed better than
   with the default empty dictionary.

     Depending on the size of the compression data structures selected by
   deflateInit or deflateInit2, a part of the dictionary may in effect be
   discarded, for example if the dictionary is larger than the window size
   provided in deflateInit or deflateInit2.  Thus the strings most likely to be
   useful should be put at the end of the dictionary, not at the front.  In
   addition, the current implementation of deflate will use at most the window
   size minus 262 bytes of the provided dictionary.

     Upon return of this function, strm->adler is set to the adler32 value
   of the dictionary; the decompressor may later use this value to determine
   which dictionary has been used by the compressor.  (The adler32 value
   applies to the whole dictionary even if only a subset of the dictionary is
   actually used by the compressor.) If a raw deflate was requested, then the
   adler32 value is not computed and strm->adler is not set.

     deflateSetDictionary returns Z_OK if success, or Z_STREAM_ERROR if a
   parameter is invalid (e.g.  dictionary being Z_NULL) or the stream state is
   inconsistent (for example if deflate has already been called for this stream
   or if not at a block boundary for raw deflate).  deflateSetDictionary does
   not perform any compression: this will be done by deflate().
*/

 int deflateCopy (z_streamp dest,
                                    z_streamp source);
/*
     Sets the destination stream as a complete copy of the source stream.

     This function can be useful when several compression strategies will be
   tried, for example when there are several ways of pre-processing the input
   data with a filter.  The streams that will be discarded should then be freed
   by calling deflateEnd.  Note that deflateCopy duplicates the internal
   compression state which can be quite large, so this strategy is slow and can
   consume lots of memory.

     deflateCopy returns Z_OK if success, Z_MEM_ERROR if there was not
   enough memory, Z_STREAM_ERROR if the source stream state was inconsistent
   (such as zalloc being Z_NULL).  msg is left unchanged in both source and
   destination.
*/

 int deflateReset (z_streamp strm);
/*
     This function is equivalent to deflateEnd followed by deflateInit,
   but does not free and reallocate all the internal compression state.  The
   stream will keep the same compression level and any other attributes that
   may have been set by deflateInit2.

     deflateReset returns Z_OK if success, or Z_STREAM_ERROR if the source
   stream state was inconsistent (such as zalloc or state being Z_NULL).
*/

 int deflateParams (z_streamp strm,
                                      int level,
                                      int strategy);
/*
     Dynamically update the compression level and compression strategy.  The
   interpretation of level and strategy is as in deflateInit2.  This can be
   used to switch between compression and straight copy of the input data, or
   to switch to a different kind of input data requiring a different strategy.
   If the compression level is changed, the input available so far is
   compressed with the old level (and may be flushed); the new level will take
   effect only at the next call of deflate().

     Before the call of deflateParams, the stream state must be set as for
   a call of deflate(), since the currently available input may have to be
   compressed and flushed.  In particular, strm->avail_out must be non-zero.

     deflateParams returns Z_OK if success, Z_STREAM_ERROR if the source
   stream state was inconsistent or if a parameter was invalid, Z_BUF_ERROR if
   strm->avail_out was zero.
*/

 int deflateTune (z_streamp strm,
                                    int good_length,
                                    int max_lazy,
                                    int nice_length,
                                    int max_chain);
/*
     Fine tune deflate's internal compression parameters.  This should only be
   used by someone who understands the algorithm used by zlib's deflate for
   searching for the best matching string, and even then only by the most
   fanatic optimizer trying to squeeze out the last compressed bit for their
   specific input data.  Read the deflate.c source code for the meaning of the
   max_lazy, good_length, nice_length, and max_chain parameters.

     deflateTune() can be called after deflateInit() or deflateInit2(), and
   returns Z_OK on success, or Z_STREAM_ERROR for an invalid deflate stream.
 */

 uLong deflateBound (z_streamp strm,
                                       uLong sourceLen);
/*
     deflateBound() returns an upper bound on the compressed size after
   deflation of sourceLen bytes.  It must be called after deflateInit() or
   deflateInit2(), and after deflateSetHeader(), if used.  This would be used
   to allocate an output buffer for deflation in a single pass, and so would be
   called before deflate().  If that first deflate() call is provided the
   sourceLen input bytes, an output buffer allocated to the size returned by
   deflateBound(), and the flush value Z_FINISH, then deflate() is guaranteed
   to return Z_STREAM_END.  Note that it is possible for the compressed size to
   be larger than the value returned by deflateBound() if flush options other
   than Z_FINISH or Z_NO_FLUSH are used.
*/

 int deflatePending (z_streamp strm,
                                       unsigned *pending,
                                       int *bits);
/*
     deflatePending() returns the number of bytes and bits of output that have
   been generated, but not yet provided in the available output.  The bytes not
   provided would be due to the available output space having being consumed.
   The number of bits of output not provided are between 0 and 7, where they
   await more bits to join them in order to fill out a full byte.  If pending
   or bits are Z_NULL, then those values are not set.

     deflatePending returns Z_OK if success, or Z_STREAM_ERROR if the source
   stream state was inconsistent.
 */

 int deflatePrime (z_streamp strm,
                                     int bits,
                                     int value);
/*
     deflatePrime() inserts bits in the deflate output stream.  The intent
   is that this function is used to start off the deflate output with the bits
   leftover from a previous deflate stream when appending to it.  As such, this
   function can only be used for raw deflate, and must be used before the first
   deflate() call after a deflateInit2() or deflateReset().  bits must be less
   than or equal to 16, and that many of the least significant bits of value
   will be inserted in the output.

     deflatePrime returns Z_OK if success, Z_BUF_ERROR if there was not enough
   room in the internal buffer to insert the bits, or Z_STREAM_ERROR if the
   source stream state was inconsistent.
*/

 int deflateSetHeader (z_streamp strm,
                                         gz_headerp head);
/*
     deflateSetHeader() provides gzip header information for when a gzip
   stream is requested by deflateInit2().  deflateSetHeader() may be called
   after deflateInit2() or deflateReset() and before the first call of
   deflate().  The text, time, os, extra field, name, and comment information
   in the provided gz_header structure are written to the gzip header (xflag is
   ignored -- the extra flags are set according to the compression level).  The
   caller must assure that, if not Z_NULL, name and comment are terminated with
   a zero byte, and that if extra is not Z_NULL, that extra_len bytes are
   available there.  If hcrc is true, a gzip header crc is included.  Note that
   the current versions of the command-line version of gzip (up through version
   1.3.x) do not support header crc's, and will report that it is a "multi-part
   gzip file" and give up.

     If deflateSetHeader is not used, the default gzip header has text false,
   the time set to zero, and os set to 255, with no extra, name, or comment
   fields.  The gzip header is returned to the default state by deflateReset().

     deflateSetHeader returns Z_OK if success, or Z_STREAM_ERROR if the source
   stream state was inconsistent.
*/

/*
 int inflateInit2 (z_streamp strm,
                                     int  windowBits);

     This is another version of inflateInit with an extra parameter.  The
   fields next_in, avail_in, zalloc, zfree and opaque must be initialized
   before by the caller.

     The windowBits parameter is the base two logarithm of the maximum window
   size (the size of the history buffer).  It should be in the range 8..15 for
   this version of the library.  The default value is 15 if inflateInit is used
   instead.  windowBits must be greater than or equal to the windowBits value
   provided to deflateInit2() while compressing, or it must be equal to 15 if
   deflateInit2() was not used.  If a compressed stream with a larger window
   size is given as input, inflate() will return with the error code
   Z_DATA_ERROR instead of trying to allocate a larger window.

     windowBits can also be zero to request that inflate use the window size in
   the zlib header of the compressed stream.

     windowBits can also be -8..-15 for raw inflate.  In this case, -windowBits
   determines the window size.  inflate() will then process raw deflate data,
   not looking for a zlib or gzip header, not generating a check value, and not
   looking for any check values for comparison at the end of the stream.  This
   is for use with other formats that use the deflate compressed data format
   such as zip.  Those formats provide their own check values.  If a custom
   format is developed using the raw deflate format for compressed data, it is
   recommended that a check value such as an adler32 or a crc32 be applied to
   the uncompressed data as is done in the zlib, gzip, and zip formats.  For
   most applications, the zlib format should be used as is.  Note that comments
   above on the use in deflateInit2() applies to the magnitude of windowBits.

     windowBits can also be greater than 15 for optional gzip decoding.  Add
   32 to windowBits to enable zlib and gzip decoding with automatic header
   detection, or add 16 to decode only the gzip format (the zlib format will
   return a Z_DATA_ERROR).  If a gzip stream is being decoded, strm->adler is a
   crc32 instead of an adler32.

     inflateInit2 returns Z_OK if success, Z_MEM_ERROR if there was not enough
   memory, Z_VERSION_ERROR if the zlib library version is incompatible with the
   version assumed by the caller, or Z_STREAM_ERROR if the parameters are
   invalid, such as a null pointer to the structure.  msg is set to null if
   there is no error message.  inflateInit2 does not perform any decompression
   apart from possibly reading the zlib header if present: actual decompression
   will be done by inflate().  (So next_in and avail_in may be modified, but
   next_out and avail_out are unused and unchanged.) The current implementation
   of inflateInit2() does not process any header information -- that is
   deferred until inflate() is called.
*/

 int inflateSetDictionary (z_streamp strm,
                                             const Bytef *dictionary,
                                             uInt  dictLength);
/*
     Initializes the decompression dictionary from the given uncompressed byte
   sequence.  This function must be called immediately after a call of inflate,
   if that call returned Z_NEED_DICT.  The dictionary chosen by the compressor
   can be determined from the adler32 value returned by that call of inflate.
   The compressor and decompressor must use exactly the same dictionary (see
   deflateSetDictionary).  For raw inflate, this function can be called at any
   time to set the dictionary.  If the provided dictionary is smaller than the
   window and there is already data in the window, then the provided dictionary
   will amend what's there.  The application must insure that the dictionary
   that was used for compression is provided.

     inflateSetDictionary returns Z_OK if success, Z_STREAM_ERROR if a
   parameter is invalid (e.g.  dictionary being Z_NULL) or the stream state is
   inconsistent, Z_DATA_ERROR if the given dictionary doesn't match the
   expected one (incorrect adler32 value).  inflateSetDictionary does not
   perform any decompression: this will be done by subsequent calls of
   inflate().
*/

 int inflateGetDictionary (z_streamp strm,
                                             Bytef *dictionary,
                                             uInt  *dictLength);
/*
     Returns the sliding dictionary being maintained by inflate.  dictLength is
   set to the number of bytes in the dictionary, and that many bytes are copied
   to dictionary.  dictionary must have enough space, where 32768 bytes is
   always enough.  If inflateGetDictionary() is called with dictionary equal to
   Z_NULL, then only the dictionary length is returned, and nothing is copied.
   Similary, if dictLength is Z_NULL, then it is not set.

     inflateGetDictionary returns Z_OK on success, or Z_STREAM_ERROR if the
   stream state is inconsistent.
*/

 int inflateSync (z_streamp strm);
/*
     Skips invalid compressed data until a possible full flush point (see above
   for the description of deflate with Z_FULL_FLUSH) can be found, or until all
   available input is skipped.  No output is provided.

     inflateSync searches for a 00 00 FF FF pattern in the compressed data.
   All full flush points have this pattern, but not all occurrences of this
   pattern are full flush points.

     inflateSync returns Z_OK if a possible full flush point has been found,
   Z_BUF_ERROR if no more input was provided, Z_DATA_ERROR if no flush point
   has been found, or Z_STREAM_ERROR if the stream structure was inconsistent.
   In the success case, the application may save the current current value of
   total_in which indicates where valid compressed data was found.  In the
   error case, the application may repeatedly call inflateSync, providing more
   input each time, until success or end of the input data.
*/

 int inflateCopy (z_streamp dest,
                                    z_streamp source);
/*
     Sets the destination stream as a complete copy of the source stream.

     This function can be useful when randomly accessing a large stream.  The
   first pass through the stream can periodically record the inflate state,
   allowing restarting inflate at those points when randomly accessing the
   stream.

     inflateCopy returns Z_OK if success, Z_MEM_ERROR if there was not
   enough memory, Z_STREAM_ERROR if the source stream state was inconsistent
   (such as zalloc being Z_NULL).  msg is left unchanged in both source and
   destination.
*/

 int inflateReset (z_streamp strm);
/*
     This function is equivalent to inflateEnd followed by inflateInit,
   but does not free and reallocate all the internal decompression state.  The
   stream will keep attributes that may have been set by inflateInit2.

     inflateReset returns Z_OK if success, or Z_STREAM_ERROR if the source
   stream state was inconsistent (such as zalloc or state being Z_NULL).
*/

 int inflateReset2 (z_streamp strm,
                                      int windowBits);
/*
     This function is the same as inflateReset, but it also permits changing
   the wrap and window size requests.  The windowBits parameter is interpreted
   the same as it is for inflateInit2.

     inflateReset2 returns Z_OK if success, or Z_STREAM_ERROR if the source
   stream state was inconsistent (such as zalloc or state being Z_NULL), or if
   the windowBits parameter is invalid.
*/

 int inflatePrime (z_streamp strm,
                                     int bits,
                                     int value);
/*
     This function inserts bits in the inflate input stream.  The intent is
   that this function is used to start inflating at a bit position in the
   middle of a byte.  The provided bits will be used before any bytes are used
   from next_in.  This function should only be used with raw inflate, and
   should be used before the first inflate() call after inflateInit2() or
   inflateReset().  bits must be less than or equal to 16, and that many of the
   least significant bits of value will be inserted in the input.

     If bits is negative, then the input stream bit buffer is emptied.  Then
   inflatePrime() can be called again to put bits in the buffer.  This is used
   to clear out bits leftover after feeding inflate a block description prior
   to feeding inflate codes.

     inflatePrime returns Z_OK if success, or Z_STREAM_ERROR if the source
   stream state was inconsistent.
*/

 long  inflateMark (z_streamp strm);
/*
     This function returns two values, one in the lower 16 bits of the return
   value, and the other in the remaining upper bits, obtained by shifting the
   return value down 16 bits.  If the upper value is -1 and the lower value is
   zero, then inflate() is currently decoding information outside of a block.
   If the upper value is -1 and the lower value is non-zero, then inflate is in
   the middle of a stored block, with the lower value equaling the number of
   bytes from the input remaining to copy.  If the upper value is not -1, then
   it is the number of bits back from the current bit position in the input of
   the code (literal or length/distance pair) currently being processed.  In
   that case the lower value is the number of bytes already emitted for that
   code.

     A code is being processed if inflate is waiting for more input to complete
   decoding of the code, or if it has completed decoding but is waiting for
   more output space to write the literal or match data.

     inflateMark() is used to mark locations in the input data for random
   access, which may be at bit positions, and to note those cases where the
   output of a code may span boundaries of random access blocks.  The current
   location in the input stream can be determined from avail_in and data_type
   as noted in the description for the Z_BLOCK flush parameter for inflate.

     inflateMark returns the value noted above or -1 << 16 if the provided
   source stream state was inconsistent.
*/

 int  inflateGetHeader (z_streamp strm,
                                         gz_headerp head);
/*
     inflateGetHeader() requests that gzip header information be stored in the
   provided gz_header structure.  inflateGetHeader() may be called after
   inflateInit2() or inflateReset(), and before the first call of inflate().
   As inflate() processes the gzip stream, head->done is zero until the header
   is completed, at which time head->done is set to one.  If a zlib stream is
   being decoded, then head->done is set to -1 to indicate that there will be
   no gzip header information forthcoming.  Note that Z_BLOCK or Z_TREES can be
   used to force inflate() to return immediately after header processing is
   complete and before any actual data is decompressed.

     The text, time, xflags, and os fields are filled in with the gzip header
   contents.  hcrc is set to true if there is a header CRC.  (The header CRC
   was valid if done is set to one.) If extra is not Z_NULL, then extra_max
   contains the maximum number of bytes to write to extra.  Once done is true,
   extra_len contains the actual extra field length, and extra contains the
   extra field, or that field truncated if extra_max is less than extra_len.
   If name is not Z_NULL, then up to name_max characters are written there,
   terminated with a zero unless the length is greater than name_max.  If
   comment is not Z_NULL, then up to comm_max characters are written there,
   terminated with a zero unless the length is greater than comm_max.  When any
   of extra, name, or comment are not Z_NULL and the respective field is not
   present in the header, then that field is set to Z_NULL to signal its
   absence.  This allows the use of deflateSetHeader() with the returned
   structure to duplicate the header.  However if those fields are set to
   allocated memory, then the application will need to save those pointers
   elsewhere so that they can be eventually freed.

     If inflateGetHeader is not used, then the header information is simply
   discarded.  The header is always checked for validity, including the header
   CRC if present.  inflateReset() will reset the process to discard the header
   information.  The application would need to call inflateGetHeader() again to
   retrieve the header from the next gzip stream.

     inflateGetHeader returns Z_OK if success, or Z_STREAM_ERROR if the source
   stream state was inconsistent.
*/

/*
 int  inflateBackInit (z_streamp strm, int windowBits,
                                        unsigned char FAR *window);

     Initialize the internal stream state for decompression using inflateBack()
   calls.  The fields zalloc, zfree and opaque in strm must be initialized
   before the call.  If zalloc and zfree are Z_NULL, then the default library-
   derived memory allocation routines are used.  windowBits is the base two
   logarithm of the window size, in the range 8..15.  window is a caller
   supplied buffer of that size.  Except for special applications where it is
   assured that deflate was used with small window sizes, windowBits must be 15
   and a 32K byte window must be supplied to be able to decompress general
   deflate streams.

     See inflateBack() for the usage of these routines.

     inflateBackInit will return Z_OK on success, Z_STREAM_ERROR if any of
   the parameters are invalid, Z_MEM_ERROR if the internal state could not be
   allocated, or Z_VERSION_ERROR if the version of the library does not match
   the version of the header file.
*/

typedef unsigned (*in_func) (void FAR *,
                                z_const unsigned char FAR * FAR *);
typedef int (*out_func) (void FAR *, unsigned char FAR *, unsigned);

 int  inflateBack (z_streamp strm,
                                    in_func in, void FAR *in_desc,
                                    out_func out, void FAR *out_desc);
/*
     inflateBack() does a raw inflate with a single call using a call-back
   interface for input and output.  This is potentially more efficient than
   inflate() for file i/o applications, in that it avoids copying between the
   output and the sliding window by simply making the window itself the output
   buffer.  inflate() can be faster on modern CPUs when used with large
   buffers.  inflateBack() trusts the application to not change the output
   buffer passed by the output function, at least until inflateBack() returns.

     inflateBackInit() must be called first to allocate the internal state
   and to initialize the state with the user-provided window buffer.
   inflateBack() may then be used multiple times to inflate a complete, raw
   deflate stream with each call.  inflateBackEnd() is then called to free the
   allocated state.

     A raw deflate stream is one with no zlib or gzip header or trailer.
   This routine would normally be used in a utility that reads zip or gzip
   files and writes out uncompressed files.  The utility would decode the
   header and process the trailer on its own, hence this routine expects only
   the raw deflate stream to decompress.  This is different from the normal
   behavior of inflate(), which expects either a zlib or gzip header and
   trailer around the deflate stream.

     inflateBack() uses two subroutines supplied by the caller that are then
   called by inflateBack() for input and output.  inflateBack() calls those
   routines until it reads a complete deflate stream and writes out all of the
   uncompressed data, or until it encounters an error.  The function's
   parameters and return types are defined above in the in_func and out_func
   typedefs.  inflateBack() will call in(in_desc, &buf) which should return the
   number of bytes of provided input, and a pointer to that input in buf.  If
   there is no input available, in() must return zero--buf is ignored in that
   case--and inflateBack() will return a buffer error.  inflateBack() will call
   out(out_desc, buf, len) to write the uncompressed data buf[0..len-1].  out()
   should return zero on success, or non-zero on failure.  If out() returns
   non-zero, inflateBack() will return with an error.  Neither in() nor out()
   are permitted to change the contents of the window provided to
   inflateBackInit(), which is also the buffer that out() uses to write from.
   The length written by out() will be at most the window size.  Any non-zero
   amount of input may be provided by in().

     For convenience, inflateBack() can be provided input on the first call by
   setting strm->next_in and strm->avail_in.  If that input is exhausted, then
   in() will be called.  Therefore strm->next_in must be initialized before
   calling inflateBack().  If strm->next_in is Z_NULL, then in() will be called
   immediately for input.  If strm->next_in is not Z_NULL, then strm->avail_in
   must also be initialized, and then if strm->avail_in is not zero, input will
   initially be taken from strm->next_in[0 ..  strm->avail_in - 1].

     The in_desc and out_desc parameters of inflateBack() is passed as the
   first parameter of in() and out() respectively when they are called.  These
   descriptors can be optionally used to pass any information that the caller-
   supplied in() and out() functions need to do their job.

     On return, inflateBack() will set strm->next_in and strm->avail_in to
   pass back any unused input that was provided by the last in() call.  The
   return values of inflateBack() can be Z_STREAM_END on success, Z_BUF_ERROR
   if in() or out() returned an error, Z_DATA_ERROR if there was a format error
   in the deflate stream (in which case strm->msg is set to indicate the nature
   of the error), or Z_STREAM_ERROR if the stream was not properly initialized.
   In the case of Z_BUF_ERROR, an input or output error can be distinguished
   using strm->next_in which will be Z_NULL only if in() returned an error.  If
   strm->next_in is not Z_NULL, then the Z_BUF_ERROR was due to out() returning
   non-zero.  (in() will always be called before out(), so strm->next_in is
   assured to be defined if out() returns non-zero.) Note that inflateBack()
   cannot return Z_OK.
*/

 int  inflateBackEnd (z_streamp strm);
/*
     All memory allocated by inflateBackInit() is freed.

     inflateBackEnd() returns Z_OK on success, or Z_STREAM_ERROR if the stream
   state was inconsistent.
*/

 uLong  zlibCompileFlags (void);
/* Return flags indicating compile-time options.

    Type sizes, two bits each, 00 = 16 bits, 01 = 32, 10 = 64, 11 = other:
     1.0: size of uInt
     3.2: size of uLong
     5.4: size of voidpf (pointer)
     7.6: size of z_off_t

    Compiler, assembler, and debug options:
     8: DEBUG
     9: ASMV or ASMINF -- use ASM code
     10: ZLIB_WINAPI -- exported functions use the WINAPI calling convention
     11: 0 (reserved)

    One-time table building (smaller code, but not thread-safe if true):
     12: BUILDFIXED -- build static block decoding tables when needed
     13: DYNAMIC_CRC_TABLE -- build CRC calculation tables when needed
     14,15: 0 (reserved)

    Library content (indicates missing functionality):
     16: NO_GZCOMPRESS -- gz* functions cannot compress (to avoid linking
                          deflate code when not needed)
     17: NO_GZIP -- deflate can't write gzip streams, and inflate can't detect
                    and decode gzip streams (to avoid linking crc code)
     18-19: 0 (reserved)

    Operation variations (changes in library functionality):
     20: PKZIP_BUG_WORKAROUND -- slightly more permissive inflate
     21: FASTEST -- deflate algorithm with only one, lowest compression level
     22,23: 0 (reserved)

    The sprintf variant used by gzprintf (zero is best):
     24: 0 = vs*, 1 = s* -- 1 means limited to 20 arguments after the format
     25: 0 = *nprintf, 1 = *printf -- 1 means gzprintf() not secure!
     26: 0 = returns value, 1 = void -- 1 means inferred string length returned

    Remainder:
     27-31: 0 (reserved)
 */

#ifndef Z_SOLO

                        /* utility functions */

/*
     The following utility functions are implemented on top of the basic
   stream-oriented functions.  To simplify the interface, some default options
   are assumed (compression level and memory usage, standard memory allocation
   functions).  The source code of these utility functions can be modified if
   you need special options.
*/

 int  compress (Bytef *dest,   uLongf *destLen,
                                 const Bytef *source, uLong sourceLen);
/*
     Compresses the source buffer into the destination buffer.  sourceLen is
   the byte length of the source buffer.  Upon entry, destLen is the total size
   of the destination buffer, which must be at least the value returned by
   compressBound(sourceLen).  Upon exit, destLen is the actual size of the
   compressed buffer.

     compress returns Z_OK if success, Z_MEM_ERROR if there was not
   enough memory, Z_BUF_ERROR if there was not enough room in the output
   buffer.
*/

 int  compress2 (Bytef *dest,   uLongf *destLen,
                                  const Bytef *source, uLong sourceLen,
                                  int level);
/*
     Compresses the source buffer into the destination buffer.  The level
   parameter has the same meaning as in deflateInit.  sourceLen is the byte
   length of the source buffer.  Upon entry, destLen is the total size of the
   destination buffer, which must be at least the value returned by
   compressBound(sourceLen).  Upon exit, destLen is the actual size of the
   compressed buffer.

     compress2 returns Z_OK if success, Z_MEM_ERROR if there was not enough
   memory, Z_BUF_ERROR if there was not enough room in the output buffer,
   Z_STREAM_ERROR if the level parameter is invalid.
*/

 uLong  compressBound (uLong sourceLen);
/*
     compressBound() returns an upper bound on the compressed size after
   compress() or compress2() on sourceLen bytes.  It would be used before a
   compress() or compress2() call to allocate the destination buffer.
*/

 int  uncompress (unsigned char *dest,   uint32_t *destLen,
       const unsigned char *source, uint32_t sourceLen);
/*
     Decompresses the source buffer into the destination buffer.  sourceLen is
   the byte length of the source buffer.  Upon entry, destLen is the total size
   of the destination buffer, which must be large enough to hold the entire
   uncompressed data.  (The size of the uncompressed data must have been saved
   previously by the compressor and transmitted to the decompressor by some
   mechanism outside the scope of this compression library.) Upon exit, destLen
   is the actual size of the uncompressed buffer.

     uncompress returns Z_OK if success, Z_MEM_ERROR if there was not
   enough memory, Z_BUF_ERROR if there was not enough room in the output
   buffer, or Z_DATA_ERROR if the input data was corrupted or incomplete.  In
   the case where there is not enough room, uncompress() will fill the output
   buffer with the uncompressed data up to that point.
*/

                        /* gzip file access functions */

/*
     This library supports reading and writing files in gzip (.gz) format with
   an interface similar to that of stdio, using the functions that start with
   "gz".  The gzip format is different from the zlib format.  gzip is a gzip
   wrapper, documented in RFC 1952, wrapped around a deflate stream.
*/

typedef struct gzFile_s *gzFile;    /* semi-opaque gzip file descriptor */

/*
 gzFile  gzopen (const char *path, const char *mode);

     Opens a gzip (.gz) file for reading or writing.  The mode parameter is as
   in fopen ("rb" or "wb") but can also include a compression level ("wb9") or
   a strategy: 'f' for filtered data as in "wb6f", 'h' for Huffman-only
   compression as in "wb1h", 'R' for run-length encoding as in "wb1R", or 'F'
   for fixed code compression as in "wb9F".  (See the description of
   deflateInit2 for more information about the strategy parameter.)  'T' will
   request transparent writing or appending with no compression and not using
   the gzip format.

     "a" can be used instead of "w" to request that the gzip stream that will
   be written be appended to the file.  "+" will result in an error, since
   reading and writing to the same gzip file is not supported.  The addition of
   "x" when writing will create the file exclusively, which fails if the file
   already exists.  On systems that support it, the addition of "e" when
   reading or writing will set the flag to close the file on an execve() call.

     These functions, as well as gzip, will read and decode a sequence of gzip
   streams in a file.  The append function of gzopen() can be used to create
   such a file.  (Also see gzflush() for another way to do this.)  When
   appending, gzopen does not test whether the file begins with a gzip stream,
   nor does it look for the end of the gzip streams to begin appending.  gzopen
   will simply append a gzip stream to the existing file.

     gzopen can be used to read a file which is not in gzip format; in this
   case gzread will directly read from the file without decompression.  When
   reading, this will be detected automatically by looking for the magic two-
   byte gzip header.

     gzopen returns NULL if the file could not be opened, if there was
   insufficient memory to allocate the gzFile state, or if an invalid mode was
   specified (an 'r', 'w', or 'a' was not provided, or '+' was provided).
   errno can be checked to determine if the reason gzopen failed was that the
   file could not be opened.
*/

 gzFile  gzdopen (int fd, const char *mode);
/*
     gzdopen associates a gzFile with the file descriptor fd.  File descriptors
   are obtained from calls like open, dup, creat, pipe or fileno (if the file
   has been previously opened with fopen).  The mode parameter is as in gzopen.

     The next call of gzclose on the returned gzFile will also close the file
   descriptor fd, just like fclose(fdopen(fd, mode)) closes the file descriptor
   fd.  If you want to keep fd open, use fd = dup(fd_keep); gz = gzdopen(fd,
   mode);.  The duplicated descriptor should be saved to avoid a leak, since
   gzdopen does not close fd if it fails.  If you are using fileno() to get the
   file descriptor from a FILE *, then you will have to use dup() to avoid
   double-close()ing the file descriptor.  Both gzclose() and fclose() will
   close the associated file descriptor, so they need to have different file
   descriptors.

     gzdopen returns NULL if there was insufficient memory to allocate the
   gzFile state, if an invalid mode was specified (an 'r', 'w', or 'a' was not
   provided, or '+' was provided), or if fd is -1.  The file descriptor is not
   used until the next gz* read, write, seek, or close operation, so gzdopen
   will not detect if fd is invalid (unless fd is -1).
*/

 int  gzbuffer (gzFile file, unsigned size);
/*
     Set the internal buffer size used by this library's functions.  The
   default buffer size is 8192 bytes.  This function must be called after
   gzopen() or gzdopen(), and before any other calls that read or write the
   file.  The buffer memory allocation is always deferred to the first read or
   write.  Two buffers are allocated, either both of the specified size when
   writing, or one of the specified size and the other twice that size when
   reading.  A larger buffer size of, for example, 64K or 128K bytes will
   noticeably increase the speed of decompression (reading).

     The new buffer size also affects the maximum length for gzprintf().

     gzbuffer() returns 0 on success, or -1 on failure, such as being called
   too late.
*/

 int  gzsetparams (gzFile file, int level, int strategy);
/*
     Dynamically update the compression level or strategy.  See the description
   of deflateInit2 for the meaning of these parameters.

     gzsetparams returns Z_OK if success, or Z_STREAM_ERROR if the file was not
   opened for writing.
*/

 int  gzread (gzFile file, voidp buf, unsigned len);
/*
     Reads the given number of uncompressed bytes from the compressed file.  If
   the input file is not in gzip format, gzread copies the given number of
   bytes into the buffer directly from the file.

     After reaching the end of a gzip stream in the input, gzread will continue
   to read, looking for another gzip stream.  Any number of gzip streams may be
   concatenated in the input file, and will all be decompressed by gzread().
   If something other than a gzip stream is encountered after a gzip stream,
   that remaining trailing garbage is ignored (and no error is returned).

     gzread can be used to read a gzip file that is being concurrently written.
   Upon reaching the end of the input, gzread will return with the available
   data.  If the error code returned by gzerror is Z_OK or Z_BUF_ERROR, then
   gzclearerr can be used to clear the end of file indicator in order to permit
   gzread to be tried again.  Z_OK indicates that a gzip stream was completed
   on the last gzread.  Z_BUF_ERROR indicates that the input file ended in the
   middle of a gzip stream.  Note that gzread does not return -1 in the event
   of an incomplete gzip stream.  This error is deferred until gzclose(), which
   will return Z_BUF_ERROR if the last gzread ended in the middle of a gzip
   stream.  Alternatively, gzerror can be used before gzclose to detect this
   case.

     gzread returns the number of uncompressed bytes actually read, less than
   len for end of file, or -1 for error.
*/

 int  gzwrite (gzFile file,
                                voidpc buf, unsigned len);
/*
     Writes the given number of uncompressed bytes into the compressed file.
   gzwrite returns the number of uncompressed bytes written or 0 in case of
   error.
*/

 int gzprintf Z_ARG((gzFile file, const char *format, ...));
/*
     Converts, formats, and writes the arguments to the compressed file under
   control of the format string, as in fprintf.  gzprintf returns the number of
   uncompressed bytes actually written, or 0 in case of error.  The number of
   uncompressed bytes written is limited to 8191, or one less than the buffer
   size given to gzbuffer().  The caller should assure that this limit is not
   exceeded.  If it is exceeded, then gzprintf() will return an error (0) with
   nothing written.  In this case, there may also be a buffer overflow with
   unpredictable consequences, which is possible only if zlib was compiled with
   the insecure functions sprintf() or vsprintf() because the secure snprintf()
   or vsnprintf() functions were not available.  This can be determined using
   zlibCompileFlags().
*/

 int  gzputs (gzFile file, const char *s);
/*
     Writes the given null-terminated string to the compressed file, excluding
   the terminating null character.

     gzputs returns the number of characters written, or -1 in case of error.
*/

 char *  gzgets (gzFile file, char *buf, int len);
/*
     Reads bytes from the compressed file until len-1 characters are read, or a
   newline character is read and transferred to buf, or an end-of-file
   condition is encountered.  If any characters are read or if len == 1, the
   string is terminated with a null character.  If no characters are read due
   to an end-of-file or len < 1, then the buffer is left untouched.

     gzgets returns buf which is a null-terminated string, or it returns NULL
   for end-of-file or in case of error.  If there was an error, the contents at
   buf are indeterminate.
*/

 int  gzputc (gzFile file, int c);
/*
     Writes c, converted to an unsigned char, into the compressed file.  gzputc
   returns the value that was written, or -1 in case of error.
*/

 int  gzgetc (gzFile file);
/*
     Reads one byte from the compressed file.  gzgetc returns this byte or -1
   in case of end of file or error.  This is implemented as a macro for speed.
   As such, it does not do all of the checking the other functions do.  I.e.
   it does not check to see if file is NULL, nor whether the structure file
   points to has been clobbered or not.
*/

 int  gzungetc (int c, gzFile file);
/*
     Push one character back onto the stream to be read as the first character
   on the next read.  At least one character of push-back is allowed.
   gzungetc() returns the character pushed, or -1 on failure.  gzungetc() will
   fail if c is -1, and may fail if a character has been pushed but not read
   yet.  If gzungetc is used immediately after gzopen or gzdopen, at least the
   output buffer size of pushed characters is allowed.  (See gzbuffer above.)
   The pushed character will be discarded if the stream is repositioned with
   gzseek() or gzrewind().
*/

 int  gzflush (gzFile file, int flush);
/*
     Flushes all pending output into the compressed file.  The parameter flush
   is as in the deflate() function.  The return value is the zlib error number
   (see function gzerror below).  gzflush is only permitted when writing.

     If the flush parameter is Z_FINISH, the remaining data is written and the
   gzip stream is completed in the output.  If gzwrite() is called again, a new
   gzip stream will be started in the output.  gzread() is able to read such
   concatented gzip streams.

     gzflush should be called only when strictly necessary because it will
   degrade compression if called too often.
*/

/*
 z_off_t  gzseek (gzFile file,
                                   z_off_t offset, int whence);

     Sets the starting position for the next gzread or gzwrite on the given
   compressed file.  The offset represents a number of bytes in the
   uncompressed data stream.  The whence parameter is defined as in lseek(2);
   the value SEEK_END is not supported.

     If the file is opened for reading, this function is emulated but can be
   extremely slow.  If the file is opened for writing, only forward seeks are
   supported; gzseek then compresses a sequence of zeroes up to the new
   starting position.

     gzseek returns the resulting offset location as measured in bytes from
   the beginning of the uncompressed stream, or -1 in case of error, in
   particular if the file is opened for writing and the new starting position
   would be before the current position.
*/

 int     gzrewind (gzFile file);
/*
     Rewinds the given file. This function is supported only for reading.

     gzrewind(file) is equivalent to (int)gzseek(file, 0L, SEEK_SET)
*/

/*
 z_off_t     gztell (gzFile file);

     Returns the starting position for the next gzread or gzwrite on the given
   compressed file.  This position represents a number of bytes in the
   uncompressed data stream, and is zero when starting, even if appending or
   reading a gzip stream from the middle of a file using gzdopen().

     gztell(file) is equivalent to gzseek(file, 0L, SEEK_CUR)
*/

/*
 z_off_t  gzoffset (gzFile file);

     Returns the current offset in the file being read or written.  This offset
   includes the count of bytes that precede the gzip stream, for example when
   appending or when using gzdopen() for reading.  When reading, the offset
   does not include as yet unused buffered input.  This information can be used
   for a progress indicator.  On error, gzoffset() returns -1.
*/

 int  gzeof (gzFile file);
/*
     Returns true (1) if the end-of-file indicator has been set while reading,
   false (0) otherwise.  Note that the end-of-file indicator is set only if the
   read tried to go past the end of the input, but came up short.  Therefore,
   just like feof(), gzeof() may return false even if there is no more data to
   read, in the event that the last read request was for the exact number of
   bytes remaining in the input file.  This will happen if the input file size
   is an exact multiple of the buffer size.

     If gzeof() returns true, then the read functions will return no more data,
   unless the end-of-file indicator is reset by gzclearerr() and the input file
   has grown since the previous end of file was detected.
*/

 int  gzdirect (gzFile file);
/*
     Returns true (1) if file is being copied directly while reading, or false
   (0) if file is a gzip stream being decompressed.

     If the input file is empty, gzdirect() will return true, since the input
   does not contain a gzip stream.

     If gzdirect() is used immediately after gzopen() or gzdopen() it will
   cause buffers to be allocated to allow reading the file to determine if it
   is a gzip file.  Therefore if gzbuffer() is used, it should be called before
   gzdirect().

     When writing, gzdirect() returns true (1) if transparent writing was
   requested ("wT" for the gzopen() mode), or false (0) otherwise.  (Note:
   gzdirect() is not needed when writing.  Transparent writing must be
   explicitly requested, so the application already knows the answer.  When
   linking statically, using gzdirect() will include all of the zlib code for
   gzip file reading and decompression, which may not be desired.)
*/

 int     gzclose (gzFile file);
/*
     Flushes all pending output if necessary, closes the compressed file and
   deallocates the (de)compression state.  Note that once file is closed, you
   cannot call gzerror with file, since its structures have been deallocated.
   gzclose must not be called more than once on the same file, just as free
   must not be called more than once on the same allocation.

     gzclose will return Z_STREAM_ERROR if file is not valid, Z_ERRNO on a
   file operation error, Z_MEM_ERROR if out of memory, Z_BUF_ERROR if the
   last read ended in the middle of a gzip stream, or Z_OK on success.
*/

 int  gzclose_r (gzFile file);
 int  gzclose_w (gzFile file);
/*
     Same as gzclose(), but gzclose_r() is only for use when reading, and
   gzclose_w() is only for use when writing or appending.  The advantage to
   using these instead of gzclose() is that they avoid linking in zlib
   compression or decompression code that is not used when only reading or only
   writing respectively.  If gzclose() is used, then both compression and
   decompression code will be included the application when linking to a static
   zlib library.
*/

 const char *  gzerror (gzFile file, int *errnum);
/*
     Returns the error message for the last error which occurred on the given
   compressed file.  errnum is set to zlib error number.  If an error occurred
   in the file system and not in the compression library, errnum is set to
   Z_ERRNO and the application may consult errno to get the exact error code.

     The application must not modify the returned string.  Future calls to
   this function may invalidate the previously returned string.  If file is
   closed, then the string previously returned by gzerror will no longer be
   available.

     gzerror() should be used to distinguish errors from end-of-file for those
   functions above that do not distinguish those cases in their return values.
*/

 void  gzclearerr (gzFile file);
/*
     Clears the error and end-of-file flags for file.  This is analogous to the
   clearerr() function in stdio.  This is useful for continuing to read a gzip
   file that is being written concurrently.
*/

#endif /* !Z_SOLO */

                        /* checksum functions */

/*
     These functions are not related to compression but are exported
   anyway because they might be useful in applications using the compression
   library.
*/

uint32_t adler32 (uint32_t adler, const uint8_t *buf, size_t len);
/*
     Update a running Adler-32 checksum with the bytes buf[0..len-1] and
   return the updated checksum.  If buf is Z_NULL, this function returns the
   required initial value for the checksum.

     An Adler-32 checksum is almost as reliable as a CRC32 but can be computed
   much faster.

   Usage example:

     uLong adler = adler32(0L, Z_NULL, 0);

     while (read_buffer(buffer, length) != EOF) {
       adler = adler32(adler, buffer, length);
     }
     if (adler != original_adler) error();
*/

/*
 uLong  adler32_combine (uLong adler1, uLong adler2,
                                          z_off_t len2);

     Combine two Adler-32 checksums into one.  For two sequences of bytes, seq1
   and seq2 with lengths len1 and len2, Adler-32 checksums were calculated for
   each, adler1 and adler2.  adler32_combine() returns the Adler-32 checksum of
   seq1 and seq2 concatenated, requiring only adler1, adler2, and len2.  Note
   that the z_off_t type (like off_t) is a signed integer.  If len2 is
   negative, the result has no meaning or utility.
*/

 uLong  crc32   (uLong crc, const Bytef *buf, uInt len);
/*
     Update a running CRC-32 with the bytes buf[0..len-1] and return the
   updated CRC-32.  If buf is Z_NULL, this function returns the required
   initial value for the crc.  Pre- and post-conditioning (one's complement) is
   performed within this function so it shouldn't be done by the application.

   Usage example:

     uLong crc = crc32(0L, Z_NULL, 0);

     while (read_buffer(buffer, length) != EOF) {
       crc = crc32(crc, buffer, length);
     }
     if (crc != original_crc) error();
*/

/*
 uLong  crc32_combine (uLong crc1, uLong crc2, z_off_t len2);

     Combine two CRC-32 check values into one.  For two sequences of bytes,
   seq1 and seq2 with lengths len1 and len2, CRC-32 check values were
   calculated for each, crc1 and crc2.  crc32_combine() returns the CRC-32
   check value of seq1 and seq2 concatenated, requiring only crc1, crc2, and
   len2.
*/


                        /* various hacks, don't look :) */

/* deflateInit and inflateInit are macros to allow checking the zlib version
 * and the compiler's view of z_stream:
 */
 int  deflateInit_ (z_streamp strm, int level,
                                     const char *version, int stream_size);
 int  inflateInit_ (z_streamp strm,
                                     const char *version, int stream_size);
 int  deflateInit2_ (z_streamp strm, int  level, int  method,
                                      int windowBits, int memLevel,
                                      int strategy, const char *version,
                                      int stream_size);
 int  inflateInit2_ (z_streamp strm, int  windowBits,
                                      const char *version, int stream_size);
 int  inflateBackInit_ (z_streamp strm, int windowBits,
                                         unsigned char FAR *window,
                                         const char *version,
                                         int stream_size);
#define deflateInit(strm, level) \
        deflateInit_((strm), (level), ZLIB_VERSION, (int)sizeof(z_stream))
#define inflateInit(strm) \
        inflateInit_((strm), ZLIB_VERSION, (int)sizeof(z_stream))
#define deflateInit2(strm, level, method, windowBits, memLevel, strategy) \
        deflateInit2_((strm),(level),(method),(windowBits),(memLevel),\
                      (strategy), ZLIB_VERSION, (int)sizeof(z_stream))
#define inflateInit2(strm, windowBits) \
        inflateInit2_((strm), (windowBits), ZLIB_VERSION, \
                      (int)sizeof(z_stream))
#define inflateBackInit(strm, windowBits, window) \
        inflateBackInit_((strm), (windowBits), (window), \
                      ZLIB_VERSION, (int)sizeof(z_stream))

#ifndef Z_SOLO

/* gzgetc() macro and its supporting function and exposed data structure.  Note
 * that the real internal state is much larger than the exposed structure.
 * This abbreviated structure exposes just enough for the gzgetc() macro.  The
 * user should not mess with these exposed elements, since their names or
 * behavior could change in the future, perhaps even capriciously.  They can
 * only be used by the gzgetc() macro.  You have been warned.
 */
 int  gzgetc_ (gzFile file);  /* backward compatibility */
#ifdef Z_PREFIX_SET
#  undef z_gzgetc
#  define z_gzgetc(g) \
          ((g)->have ? ((g)->have--, (g)->pos++, *((g)->next)++) : gzgetc(g))
#else
#  define gzgetc(g) \
          ((g)->have ? ((g)->have--, (g)->pos++, *((g)->next)++) : gzgetc(g))
#endif

/* provide 64-bit offset functions if _LARGEFILE64_SOURCE defined, and/or
 * change the regular functions to 64 bits if _FILE_OFFSET_BITS is 64 (if
 * both are true, the application gets the *64 functions, and the regular
 * functions are changed to 64 bits) -- in case these are set on systems
 * without large file support, _LFS64_LARGEFILE must also be true
 */
#ifdef Z_LARGE64
    gzFile  gzopen64 (const char *, const char *);
    z_off64_t  gzseek64 (gzFile, z_off64_t, int);
    z_off64_t  gztell64 (gzFile);
    z_off64_t  gzoffset64 (gzFile);
    uLong  adler32_combine64 (uLong, uLong, z_off64_t);
    uLong  crc32_combine64 (uLong, uLong, z_off64_t);
#endif

#if !defined(ZLIB_INTERNAL) && defined(Z_WANT64)
#  ifdef Z_PREFIX_SET
#    define z_gzopen z_gzopen64
#    define z_gzseek z_gzseek64
#    define z_gztell z_gztell64
#    define z_gzoffset z_gzoffset64
#    define z_adler32_combine z_adler32_combine64
#    define z_crc32_combine z_crc32_combine64
#  else
#    define gzopen gzopen64
#    define gzseek gzseek64
#    define gztell gztell64
#    define gzoffset gzoffset64
#    define adler32_combine adler32_combine64
#    define crc32_combine crc32_combine64
#  endif
#  ifndef Z_LARGE64
      gzFile  gzopen64 (const char *, const char *);
      z_off_t  gzseek64 (gzFile, z_off_t, int);
      z_off_t  gztell64 (gzFile);
      z_off_t  gzoffset64 (gzFile);
      uLong  adler32_combine64 (uLong, uLong, z_off_t);
      uLong  crc32_combine64 (uLong, uLong, z_off_t);
#  endif
#else
    gzFile  gzopen (const char *, const char *);
    z_off_t  gzseek (gzFile, z_off_t, int);
    z_off_t  gztell (gzFile);
    z_off_t  gzoffset (gzFile);
    uLong  adler32_combine (uLong, uLong, z_off_t);
    uLong  crc32_combine (uLong, uLong, z_off_t);
#endif

#else /* Z_SOLO */

    uLong  adler32_combine (uLong, uLong, z_off_t);
    uLong  crc32_combine (uLong, uLong, z_off_t);

#endif /* !Z_SOLO */

/* hack for buggy compilers */
#if !defined(ZUTIL_H) && !defined(NO_DUMMY_DECL)
    struct internal_state {int dummy;};
#endif

/* undocumented functions */
 const char   *  zError           (int);
 int             inflateSyncPoint (z_streamp);

const uint32_t * get_crc_table(void);
 int             inflateUndermine (z_streamp, int);
 int             inflateResetKeep (z_streamp);
 int             deflateResetKeep (z_streamp);
#if defined(_WIN32) && !defined(Z_SOLO)
 gzFile          gzopen_w (const wchar_t *path,
                                            const char *mode);
#endif
#if defined(STDC) || defined(Z_HAVE_STDARG_H)
#  ifndef Z_SOLO
 int            gzvprintf Z_ARG((gzFile file,
                                                  const char *format,
                                                  va_list va));
#  endif
#endif

#ifdef __cplusplus
}
#endif

#endif /* ZLIB_H */

#else
#include <zlib.h>
#endif

#endif